Ruijie RG-S29 Series Скачать руководство пользователя страница 286

Страница: 286 / 1510

Command Reference Interface Commands

Usage Guide

Native VLAN:

A trunk port belongs to one native VLAN. A native VLAN means that the untagged packets

received/sent on the trunk port belong to the VLAN. Obviously, the default VLAN ID of the interface

(that is, the PVID in the IEEE 802.1Q) is the VLAN ID of the native VLAN. In addition, when frames

belonging to the native VLAN are sent over the trunk port, they are untagged.

Allowed-VLAN List:

By default, a trunk port sends traffic to and received traffic from all VLANs (ID 1 to 4094). However,

you can prevent the traffic from passing over the trunk by configuring allowed VLAN lists on a trunk.

Use show interfaces switchport to display configuration.

Configuration

Examples

The following example removes port 1/15 from VLAN 2.

Ruijie(config)# interface fastethernet

1/15

Ruijie(config-if)# switchport trunk allowed vlan remove

Ruijie(config-if)# end

Ruijie# show interfaces fastethernet

1/15

switchport

Switchport is enabled

Mode is trunk port

Access vlan is 1,Native vlan is 1

Protected is disabled

Vlan lists is

1,3-4094

Related

Commands

Command

Description

show interfaces

Displays the interface information.

switchport access

Configures an interface as a statics access port

and assigns it to a VLAN.

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды