Ruijie RG-S29 Series Скачать руководство пользователя страница 1419

Страница: 1419 / 1510

Command Reference VRRP Plus Commands

5.5 vrrp load-balancing

Use this command to set the VRRP Plus load balancing policy.

Use the

form of this command to restore the default setting.

vrrp

group

load-balancing

{

host-dependent

round-robin

weighted

no vrrp

group

load-balancing

{

host-dependent

round-robin

weighted

}

Parameter

Description

Parameter

Description

group

Specifies the VRRP group ID.

host-dependent

Sets the host-dependent load balancing policy, so as to use the

different virtual MACs to reply the host’s ARP request based on

different hosts.

round-robin

Sets the round-robin balancing policy, so as to use the different virtual

MACs to reply the

host’s ARP request in turn, which is the default

setting.

weighted

Sets the weight balancing policy, so as to perform the ARP reply

based on the device weight of the backup group.

Defaults

The default is round-robin.

Command

Mode

Interface configuration mode

Usage Guide

N/A

Configuration

Examples

The following example sets the load balancing policy of the VRRP Plus group1 on Layer 3 interface

GigabitEthernet0/0 as host-dependent.

Ruijie# config t

Ruijie(config)# interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)# vrrp 1 ip 192.168.1.1

Ruijie(config-if-GigabitEthernet 0/0)# vrrp 1 balance

Ruijie(config-if-GigabitEthernet 0/0)# vrrp 1 load-balancing host-dependent

Related

Commands

Command

Description

vrrp

group

balance

Enables the VRRP Plus function.

show vrrp balance

[

brief

grou

p ]

Displays the VRRP Plus running status.

show vrrp balance interface

type number

[

brief

]

Displays the VRRP Plus running status o the

specified interface.

Platform

Description

N/A

«
...
1417
1418
1419
1420
1421
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды