Ruijie RG-S29 Series Скачать руководство пользователя страница 456

Страница: 456 / 1510

Command Reference ERPS Commands

Enter configuration commands, one per line. End with CNTL/Z.

# Enable the ERPS function globally.

Ruijie(config)# erps enable

# Enter the ERPS configuration mode

Ruijie(config)# erps raps-vlan 4093

# Enable the ERPS function for the specified ring.

Ruijie(config-erps4093)# state enable

Related

Commands

Command

Description

state enable

After entering the ERPS configuration mode of

the specified ring, configure this command to

enable the ERPS protocol of this specified ring.

Platform

Description

N/A

13.3 erps monitor link-state by oam

Use this command to configure the method of monitoring the ERPS link state.

erps monitor link-state by oam vlan

vlan-id

no erps monitor link-state by oam

Parameter

Description

Parameter

Description

vlan-id

Indicates the VLAN that monitors link state.

Defaults

By default, it adopts the directly monitoring the link physical state (up or down) rather than the oam

method.

Command

Mode

Global configuration mode.

Usage Guide

For the link state monitoring, use the method of directly monitoring the link physical state (up or

down), also monitor the logic state (unidirectional fault, bidirectional fault or normal) of the link by the

OAM. By default, the former is adopted. If the OAM method is used, the inefficient link state

monitoring may cause the convergence time longer when the topology changes.

Configuration

Examples

The following example configures the method of monitoring the link state.

# Enter the privileged EXEC mode.

Ruijie# configure terminal

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды