Ruijie RG-S29 Series Скачать руководство пользователя страница 1172

Страница: 1172 / 1510

Configuration Guide DHCPv6 Snooping Commands

15.12 ipv6 dhcp snooping trust

Use this command to set the specified DHCPv6 Snooping ports as the trusted ports.

Use the

form of this command to restore the default setting.

ipv6 dhcp snooping trust

no ipv6 dhcp snooping trust

Parameter

Description

Parameter

Description

N/A

Defaults

All ports are untrusted ports by default.

Command

Mode

Interface configuration mode

Usage Guide

1. Use this command to set a port as a trusted port. The DHCPv6 Server response messages

received under the trust port are forwarded normally, but the response messages received under the

untrusted port will be discarded.

2. This command is valid only on Layer 2 wired switch ports and aggregate ports.

Configuration

Examples

The following example sets

FastEthernet

0/1

as a trust port:

Ruijie# configure terminal

Ruijie(config)# interface GigabitEthernet 0/1

Ruijie(config-if)# ipv6 dhcp snooping trust

Ruijie(config-if)# end

Related

Commands

Command

Description

show ipv6 dhcp snooping

Displays the DHCPv6 Snooping configuration.

Platform

Description

N/A

15.13 ipv6 dhcp snooping vlan

Use this command to enable DHCPv6 Snooping for the specific VLAN.

Use the

form of this command to disable this function.

ipv6 dhcp snooping vlan

{

vlan-rng

{

vlan-min

[

vlan-max

] } }

ipv6 dhcp snooping vlan

{

vlan-rn

{

vlan-min

[

vlan-max

] } }

Parameter

Description

Parameter

Description

«
...
1170
1171
1172
1173
1174
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды