Ruijie RG-S29 Series Скачать руководство пользователя страница 1378

Страница: 1378 / 1510

Command Reference REUP Commands

Command

Mode

Global configuration mode.

Usage Guide

In order to reduce the link switchover and the loss of the downstream data flow, it is necessary to

enable the switch of receiving the MAC address update messages on the uplink switch.

Configuration

Examples

Ruijie(config)# mac-address-table move update transit

Related

Commands

Command

Description

mac-address-table move update transit vlan

Enables REUP to transmit the

mac-address-table update messages.

Platform

Description

N/A.

1.7 mac-address-table move update transit vlan

Use this command to enable REUP to transmit the mac-address update messages.

mac-address-table move update transit vlan

vid

no mac-address-table move update transit vlan

Parameter

Description

Parameter

Description

vid

ID of the VLAN transmitting MAC address update packets.

Defaults

Transmit the MAC-address update messages in the default VLAN on the port.

Command

Mode

Interface configuration mode.

Usage Guide

When a link is switched, the VLAN enabled to transmit MAC address update packets will send MAC

address update packets to its uplink device.

Configuration

Examples

The following example configures VLANs transmitting MAC address update packets:

Ruijie(config)# mac-address-table move update transit

Related

Commands

Command

Description

mac-address-table move update transit

Enables REUP to receive the

mac-address-table update messages.

Platform

N/A.

«
...
1376
1377
1378
1379
1380
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды