Ruijie RG-S29 Series Скачать руководство пользователя страница 1227

Страница: 1227 / 1510

Configuration Guide NFPP Commands

Platform

Description

N/A

21.37 icmp-guard isolate-period

Use this command to set the isolate time globally.

Use the

default

form of this command to restore the default setting.

icmp-guard isolate-period

{

seconds

permanent

}

icmp-guard isolate-period

default icmp-guard isolate-period

Parameter

Description

Parameter

Description

seconds

Sets the isolate time. The value is in the range is 0 or from 30 to

86,400 in the unit of seconds.

permanent

Permanent isolation.

Defaults

The default isolate time is 0, which means no isolation.

Command

Mode

NFPP configuration mode

Usage Guide

The isolate period can be configured globally or based on the interface. For one interface, if the

isolate period is not set based on the interface, the global value shall be adopted; or the

interface-based isolate period shall be adopted.

Configuration

Examples

The following example sets the isolate time globally to 180 seconds.

Ruijie(config)# nfpp

Ruijie(config-nfpp)# icmp-guard isolate-period 180

Related

Commands

Command

Description

nfpp icmp-guard isolate-period

Sets the isolate time on the interface.

show nfpp icmp-guard summary

Displays the configuration.

Platform

Description

N/A

21.38 icmp-guard monitored-host-limit

Use this command to set the maximum monitored host number.

Use the

default

form of this command to restore the default setting.

icmp-guard monitored-host-limit

number

«
...
1225
1226
1227
1228
1229
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды