Ruijie RG-S29 Series Скачать руководство пользователя страница 1402

Страница: 1402 / 1510

Command Reference VRRP Commands

Only IPv6 VRRP has this configuration mode.

Configuration

Examples

The following example enables the accept mode on the group 1.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

Ruijie(config-if-GigabitEthernet 0/0)#ipv6 enable

Ruijie(config-if-GigabitEthernet 0/0)#ipv6 address 2001::2/64

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ipv6 FE80::1

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ipv6 2001::1

Ruijie(config-if-GigabitEthernet 0/0)# vrrp ipv6 1 accept_mode

Platform

Description

N/A

4.5 vrrp authentication

Use this command to enable VRRP authentication.

Use the

form of this command to disable this function.

vrrp

group

authentication

string

no vrrp

group

authentication

Parameter

Description

Parameter

Description

group

VRRP group number

string

String for the VRRP group authentication (within 8 bytes, plaintext

password)

Defaults

This function is disabled by default. Even if the VRRP function is enabled, no authentication password

is configured by default.

Command

Mode

Interface configuration mode

Usage Guide

The devices in the same VRRP group must have the same authentication password configured. The

plaintext authentication password cannot provide security. It aims only to prevent/prompt the incorrect

VRRP configuration. This command is only applied to the VRRPv2 packets.

Configuration

Examples

The following example sets the authentication password for VRRP group 1.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

Ruijie(config-if-GigabitEthernet 0/0)#ip address 10.0.1.1 255.255.255.0

«
...
1400
1401
1402
1403
1404
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды