Ruijie RG-S29 Series Скачать руководство пользователя страница 320

Страница: 320 / 1510

Command Reference VLAN Commands

will not be deleted. You can run the

switchport trunk allowed

command to add the port to or remove

the port from a specified VLAN.

If a switch port is a hybrid port, the port is added to all VLANs by default. Different from a trunk port, a

hybrid port can be added to a VLAN in tag or untag mode by running the

switchport hybrid allowed

command.

Configuration

Examples

The following example configures port 1 as an access port.

Ruijie(config)#int g 0/1

Ruijie(config-if-GigabitEthernet 0/1)#switchport mode access

The following example configures port 1 as a trunk port.

Ruijie(config)#int g 0/1
Ruijie(config-if-GigabitEthernet 0/1)# switchport mode trunk

The following example configures port 1 as an uplink port.

Ruijie(config)#int g 0/1
Ruijie(config-if-GigabitEthernet 0/1)# switchport mode uplink

The following example configures port 1 as a hybrid port.

Ruijie(config)#int g 0/1
Ruijie(config-if-GigabitEthernet 0/1)# switchport mode hybrid

Related

Commands

Command

Description

switchport access

Configures an interface as a statics access port

and assigns it to a VLAN.

switchport trunk

Specifies a native VLAN and the allowed-VLAN

list for the trunkport.

Platform

Description

N/A

4.8 switchport trunk allowed vlan

Use this command to add the trunk/uplink port to the VLAN or remove a trunk/uplink port from the

VLAN. Use the

default

form of the command to restore the default setting.

switchport trunk

allowed vlan

{

all

| {

add

vlan-list

remove

vlan-list

except

vlan-list

only

vlan-list

} }

no switchport trunk

allowed vlan

default switchport trunk

allowed vlan

Parameter

Description

Parameter

Description

all

Adds the trunk/uplink port to all VLANs.

add

Adds the trunk/uplink port to the VLAN.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 320 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: