Ruijie RG-S29 Series Скачать руководство пользователя страница 325

Страница: 325 / 1510

Command Reference MAC VLAN Commands

Parameter

Description

Parameter

Description

mac-address

Specifies the MAC address.

mac-mask

Specifies the MAC address mask, with the high bits being all 1 in

binary. This field is full of F by default.

vlan-id

Specifies the VLAN corresponding to the MAC address. The range is

from 1 to 4,094.

pri_val

Specifies the 802.1p priority of the VLAN corresponding to the MAC

address. The range is from 0 to 7. The default value is 0.

Defaults

No static MAC VLAN entry is configured by default.

Command

mode

Global configuration mode

Usage Guide

Use this command to configure a static MAC VLAN entry including the MAC address, VLAN ID and

VLAN priority. Use the

form of this command to remove the static MAC VLAN entry.

Configuration

Examples

The following example configures a static MAC VLAN entry.

Ruijie(config)# mac-vlan mac-address 0001.0001.0001 vlan 100 priority 3

Ruijie(config)# mac-vlan mac-address 0002.0002.0000 mask ffff.ffff.0000 vlan

200 priority 5

Related

Commands

Command

Description

N/A

Platform

Description

N/A

5.3 show mac-vlan

Use this command to display the MAC VLAN entries.

show mac-vlan

{

all

dynamic

static

vlan

vlan-id

mac-address

mac-address

[

mask

mac-mask

]

}

Parameter

Description

Parameter

Description

all

Displays all MAC VLAN entries.

dynamic

Displays the dynamic MAC VLAN entries.

static

Displays the static MAC VLAN entries.

mac-address mac-address

Displays the MAC VLAN entry of the specified MAC address.

mask

mac-mask

Displays the MAC VLAN entry of the specified MAC address range.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды