Ruijie RG-S29 Series Скачать руководство пользователя страница 459

Страница: 459 / 1510

Command Reference ERPS Commands

Ruijie(config-mst)# exit

Ruijie(config)# erps raps-vlan 4093

Ruijie(config-erps4093)#protected-instance 2

Related

Commands

Command

Description

N/A

Platform

Description

N/A

13.6

ring-port

Use this command to configure the ERPS ring.

ring-port

west

{

interface-name1

virtual-channel

}

east

{

interface-name2

virtual-channel

}

no ring-port

Parameter

Description

Parameter

Description

interface-name1

Name of the West port.

interface-name2

Name of the East port.

Defaults

No ERPS ring is configured.

Command

Mode

EPRS configuration mode.

Usage Guide

After adding the port to the ERP ring, the trunk attribute of the port is not allowed to be modified

any more.

If the ring port is configured on the virtual-channel, this ring will be considered as a sub-ring.

Ports running the ERPS do not participate in the STP computing. ERPS, RERP and REUP do

not share the port.

Configuration

Examples

The following example is for the ERPS ring.

# Enter the privileged EXEC mode.

Ruijie# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

# Configure the link mode of the Ethernet ring port and the default VLAN.

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if)# switchport mode trunk

Ruijie(config-if)# exit

Ruijie(config)# interface fastEthernet 0/2

Ruijie(config-if)# switchport mode trunk

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды