Ruijie RG-S29 Series Скачать руководство пользователя страница 1403

Страница: 1403 / 1510

Command Reference VRRP Commands

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ip 10.0.1.20

Ruijie(config-if-GigabitEthernet 0/0)# vrrp 1 authentication x30dn78k

Platform

Description

N/A

4.6 vrrp delay

Use this command to set the reload latency of the VRRP group on the interface.

Use the

form of this command to restore the default setting.

vrrp delay

{

minimum

min-seconds

reload

reload-seconds

}

no vrrp delay

Parameter

Description

Parameter

Description

minimum

min-seconds

When the interface is up, VRRP group shall be reloaded after at least

min-seconds.

reload

reload-seconds

The reload latency of the VRRP group. If the configured

min-seconds

is more than

reload-seconds

, the actual reload latency of the VRRP

group will be min-seconds.

Defaults

This function is disabled by default.

Command

Mode

Interface configuration mode

Usage Guide

Use this command to set the reload latency of the VRRP group on the interface, when it is required

that the VRRP group shall not be reloaded immediately after the system reloads or the interface is up.

The reload latency range is 0 to 60 seconds.

Configuration

Examples

The following example sets the VRRP reload latency on E0 to 10 seconds. When E0 is up, VRRP

group 1 shall be reloaded in 10 seconds.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

Ruijie(config-if-GigabitEthernet 0/0)#vrrp delay minimum 10 reload 10

Ruijie(config-if-GigabitEthernet 0/0)#ip address 10.0.1.1 255.255.255.0

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ip 10.0.1.20

Related

Commands

Command

Description

N/A

Platform

N/A

«
...
1401
1402
1403
1404
1405
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды