Ruijie RG-S29 Series Скачать руководство пользователя страница 1029

Страница: 1029 / 1510

Configuration Guide 802.1X Commands

Since single-host only supports the single-user form, setting default-user-limit on the port manually

does not take effect in single-host mode. If you set default-user-limit on the port after setting

single-host, only one user can be permitted to use the network still.

Configuration

Examples

The following example sets the port to participate in authentication and enable port-based

authentication.

Ruijie(config-if-GigabitEthernet 0/0)# dot1x port-control-mode port-based

Related

Commands

Command

Description

show dot1x port-control

Displays the port control mode.

show running-config

Displays the configuration.

Platform

Description

N/A

4.36 dot1x private-supplicant-only

Use this command to filter non-Ruijie clients.

Use the

form of this command to restore the default setting.

dot1x private-supplicant-only

no dot1x private-supplicant-only

Parameter

Description

Parameter

Description

N/A

Defaults

This function disabled by default.

Command

Mode

Global configuration mode

Usage Guide

This command is used for authentication supporting only Ruijie clients.

Configuration

Examples

The following example filters non-Ruijie clients.

Ruijie(config)# dot1x private-supplicant-only

Related

Commands

Command

Description

show dot1x private-supplicant-only

Displays the information about the private supplicant.

Platform

Description

N/A

«
...
1027
1028
1029
1030
1031
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды