Ruijie RG-S29 Series Скачать руководство пользователя страница 292

Страница: 292 / 1510

Command Reference MAC Address Commands

Configuration

Examples

N/A

Related

Commands

Command

Description

show mac-address-table static

Displays the static MAC address.

Platform

Description

N/A

2.8 max-dynamic-mac-count

Use this command to set the maximum number of MAC address learned dynamically on the VLAN or

interface. Use the

default

form of this command to restore the default setting.

max-dynamic-mac-count

num

no max-dynamic-mac-count

default max-dynamic-mac-count

Parameter

Description

Parameter

Description

num

Sets the maximum number of MAC addresses.

Defaults

The maximum number is not set by default.

Command

Mode

VLAN configuration mode / Interface configuration mode

Usage Guide

This command is used to set the maximum number of MAC addresses learned dynamically on the

VLAN or interface.

If the number of MAC addresses dynamically learned on the VLAN or interface reaches the upper

limit, MAC address learning is disabled on the VLAN or interface.

If the number of MAC addresses reaches the upper limit when this command is configured, the

surplus MAC addresses are not cleared. Instead, they remain and then age. MAC address learning is

disabled on the VLAN or interface.

Use the

show mac-address-table max-dynamic-mac-count

command to display the maximum

number of MAC addresses learned dynamically on the VLAN or interface.

Configuration

Examples

The following example sets the maximum number of MAC addresses dynamically learned on VLAN

Ruijie#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Ruijie(config)#vlan 1

Ruijie(config-vlan)#max-dynamic-mac-count 160

The following example sets the maximum number of MAC addresses dynamically learned on

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды