Ruijie RG-S29 Series Скачать руководство пользователя страница 513

Страница: 513 / 1510

Command Reference

IPv6 Commands

Platform

Description

N/A

3.8 ipv6 mtu

Use this command to configure the MTU of IPv6 packets. Use the

form of this command to restore

the default setting.

ipv6 mtu

bytes

no ipv6 mtu

Parameter

Description

Parameter

Description

bytes

MTU of IPv6 packets, in bytes. The value ranges from 1280 to 1500.

Defaults

The default configuration is the same as the configuration of the

mtu

command.

Command

Mode

Interface configuration mode

Usage Guide

If the size of an IPv6 packet exceeds the IPv6 MTU, the RGOS software segments the packet. For all

devices in the same physical network segment, the IPv6 MTU of the interconnected interface must be

the same.

Configuration

Examples

The following example sets the IPv6 MTU of the FastEthernet 0/1 interface to 1400 bytes.

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if)# ipv6 mtu 1400

Related

Commands

Command

Description

mtu

Sets the MTU of an interface.

Platform

Description

This command cannot be used on Layer 2 devices.

3.9 ipv6 nd cache interface-limit

Use this command to set the maximum number of neighbors learned on the interface. Use the

form of this command to restore the default setting.

ipv6 nd cache interface-limit

value

no ipv6 nd cache interface-limit

Parameter

Description

Parameter

Description

value

Sets the maximum number of neighbors learned on

the interface, including the static and dynamic

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды