Ruijie RG-S29 Series Скачать руководство пользователя страница 285

Страница: 285 / 1510

Command Reference Interface Commands

Usage Guide

The ports that are set as the protected ports cannot switch on L2, but can route on L3. A protected

port can communicate with an unprotected port. Use the

show interfaces

command to display

configuration.

Configuration

Examples

The following example configures interface

gigabitethernet 1/1 as a protected port.

Ruijie(config)#interface gigabitethernet 1/1

Ruijie(config-if)# switchport protected

Related

Commands

Command

Description

show interfaces

Displays the interface information.

Platform

Description

N/A

1.37 switchport trunk

Use this command to specify a native VLAN and the allowed-VLAN list for the trunk port. Use the

form of this command to restore the default setting.

switchport trunk

{

allowed vlan

{

all

[

add

remove

except

]

vlan-list

} |

native vlan

vlan-id

}

no switchport trunk

{

allowed vlan

native vlan

}

Parameter

Description

Parameter

Description

allowed vlan

vlan-list

Configures the list of VLANs allowed on the trunk port.

vlan-list

can

be a VLAN or a range of VLANs starting with the smaller VLAN ID

and ending with the larger VLAN ID and being separated by hyphen,

for example, 10 to 20. The segments can be separated with a comma

(,), for example, 1 to 10, 20 to 25, 30, 33.

all means that the allowed VLAN list contains all the supported

VLANs;

add means to add the specified VLAN list to the allowed VLAN list;

remove means to remove the specified VLAN list from the allowed

VLAN list;

except means to add all the VLANs other than those in the specified

VLAN list to the allowed VLAN list;

native vlan

vlan-id

Configures the native VLAN.

Defaults

The allowed VLAN list is all, the Native VLAN is VLAN1.

Command

Mode

Interface configuration mode.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды