Ruijie RG-S29 Series Скачать руководство пользователя страница 923

Страница: 923 / 1510

Command Reference

IGMP Snooping Commands

Parameter

Description

Parameter

Description

seconds

Aging time from 1 to 3,600 in the unit of seconds

Defaults

The default is 300 seconds.

Command

Mode

Global configuration mode

Usage Guide

If a dynamic routing interface does not receive IGMP query packets or PIM hello packets before aged,

this interface will be deleted.

When the dynamic routing interface learning function is enabled, this command sets the aging time of

the routing interface. If the aging time is set too short, the routes may be added and deleted frequently.

Configuration

Examples

The following example sets the aging time of the routing interface that the switch learns dynamically to

100 seconds.

Ruijie(config)# ip igmp snooping dyn-mr-aging-time 100

Platform

Description

N/A

2.7 ip igmp snooping fast-leave enable

Use this command to enable the fast leave function.

Use the

default

form of this command to restore the default setting.

ip igmp snooping fast-leave enable

no ip igmp snooping fast-leave enable

default ip igmp snooping fast-leave enable

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled by default.

Command

Mode

Global configuration mode

Usage Guide

After you execute this command to enable the fast-leave function, the system will remove the

corresponding multicast group on the corresponding interface upon the receipt of the IGMP leave

message.

Subsequently, when the system receives a specific group query packet, the system does not forward it

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды