Ruijie RG-S29 Series Скачать руководство пользователя страница 282

Страница: 282 / 1510

Command Reference Interface Commands

Ruijie(config-if)# speed 100

Related

Commands

Command

Description

show interfaces

Displays the interface information.

Platform

Description

N/A

1.33 switchport

Use this command to configure a Layer 3 interface. Use the

form of this command to restore the

default setting.

switchport

no switchport

Parameter

Description

Parameter

Description

N/A

Defaults

All the interfaces are in Layer 2 mode by default.

Command

Mode

Interface configuration mode.

Usage Guide

This command is valid only for physical interfaces. The

switchport

command is used to disable the

interface and re-enable it. In this status, the device will send the information to indicate the connect

status. If the interface is changed to Layer 3 mode from Layer 2, all the attributes in Layer 2 mode will

be cleared.

Configuration

Examples

The following example configures a Layer 3 interface.

Ruijie(config-if)#

switchport

Related

Commands

Command

Description

show interfaces

Displays the interface information.

Platform

Description

N/A

1.34 switchport access

Use this command to configure an interface as a statics access port and add it to a VLAN. Use the

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды