Ruijie RG-S29 Series Скачать руководство пользователя страница 985

Страница: 985 / 1510

Configuration Guide RADIUS Commands

response packet from the Radius server within the specified time, the

Radius server is considered to be unreachable. The value is in the

range from 1 to 120 in the unit of seconds.

tries

number

Configures the successive timeout times. When sending a request

from the device to the Radius server times out for the specified times,

the device considers that the Radius server is unreachable. The

value is in the range from 1 to 100 in the unit of seconds.

Defaults

The default

time

seconds

is 60 and

tries

number

is 10.

Command

Mode

Global configuration mode

Usage Guide

If a Radius server meets the timeout and timeout times at the same time, it is considered to be

unreachable. This command is used to adjust the parameter conditions of timeout and timeout times.

Configuration

Examples

The following example sets the timeout to 120 seconds and timeout times to 20.

Ruijie(config)# radius-server dead-criteria time 120 tries 20

Related

Commands

Command

Description

radius-server host

Defines the RADIUS security server.

radius-server deadtime

Defines the duration when a device stops

sending any requests to an unreachable

Radius server.

radius-server timeout

Defines the timeout for the packet

re-transmission.

Platform

Description

N/A

2.15 radius-server deadtime

Use this command to configure the duration when a device stops sending any requests to an

unreachable Radius server.

Use the

form of this command to restore the default setting.

radius-server deadtime

minutes

no radius-server deadtime

Parameter

Description

Parameter

Description

minutes

Defines the duration in minutes when the device stops sending any

requests to the unreachable Radius server. The value is in the range

from 1 to 1,440 in the unit of minutes.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды