Ruijie RG-S29 Series Скачать руководство пользователя страница 173

Страница: 173 / 1510

Command Reference

Syslog Commands

8.31 logging synchronous

Use this command to enable synchronization function between user input and log output in line

configuration mode to prevent interruption when the user is keying in characters. Use the

form of

this command to restore the default setting.

logging synchronous

no logging synchronous

Parameter

Description

Parameter

Description

N/A

Defaults

The synchronization function between user input and log output is disabled by default.

Command

Mode

Line configuration mode

Usage Guide

This command enables synchronization function between user input and log output, preventing the

user from interrupting when keying in the characters.

Configuration

Examples

Ruijie(config)#

line console

Ruijie(config-line)#logging synchronous

Print UP-DOWN logs on the port when keying in the command, the input command will be output

again:

Ruijie# configure terminal

Oct 9 23:40:55 %LINK-5-CHANGED: Interface GigabitEthernet 0/1, changed state

to down

Oct 9 23:40:55 %LINEPROTO-5-UPDOWN: Line protocol on Interface

GigabitEthernet 0/1, changed state to DOWN

Ruijie#

configure terminal

----

the input command by the user is output

again rather than being intererupted.

Related

Commands

Command

Description

show running-config

Displays the configuration.

Platform

Description

N/A

8.32 logging trap

Use this command to set the severity of logs that are allowed to be sent to the syslog server in global

configuration mode.

Use the

form of this command to prohibit sending log messages to the Syslog

server.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды