Ruijie RG-S29 Series Скачать руководство пользователя страница 318

Страница: 318 / 1510

Command Reference VLAN Commands

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)#switchport mode hybrid

Ruijie(config-if-GigabitEthernet 0/1)#switchport hybrid allowed vlan tagged

The following example removes the hybrid port from VLAN 20.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)#switchport mode hybrid

Ruijie(config-if-GigabitEthernet 0/1)#switchport hybrid allowed
vlan remove 20

The following example adds the hybrid port to VLAN 20 and deletes all the other VLANs. The VLAN

packets going out on the port are tagged with VLAN ID.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)#switchport mode hybrid

Ruijie(config-if-GigabitEthernet 0/1)#switchport hybrid allowed
vlan only tagged 20

Related

Commands

Command

Description

N/A

Platform

Description

N/A

4.6 switchport hybrid native

Use this command to configure the native VLAN for the hybrid port. Use the

default

form of this

command to restore the default setting.

switchport hybrid

native vlan

vlan-id

no switchport hybrid native vlan

default switchport hybrid native vlan

Parameter

Description

Parameter

Description

vlan-id

Configures the native VLAN for the hybrid port.

Defaults

The default is VLAN 1.

Command

mode

Interface configuration mode

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды