Ruijie RG-S29 Series Скачать руководство пользователя страница 769

Страница: 769 / 1510

Command Reference

OSPFv2 Commands

Ruijie(config-router)# timers pacing lsa-transmit 50 20

Related

Commands

Command

Description

show ip ospf

Displays the OSPF process information,

including the router ID.

Platform

Description

N/A

2.63 timers spf

Use this command to configure the delay for SPF calculation after the OSPF receives the topology

change as well as the interval between two SPF calculations. Use the

form of this command to

restore the default setting.

timers spf

spf-delay spf-holdtime

no timers spf

Parameter

Description

Parameter

Description

spf-delay

Defines the SPF calculation waiting period in seconds. The range is

from 0 to 2147483647.After receiving the topology change, the OSPF

routing process must wait for the specified period to start the SPF

calculation.

spf-holdtime

Defines the interval between two SPF calculations in seconds. The

range is from 0 to 2147483647.When the waiting time is up but the

interval between two calculations is still elapsing, the SPF calculation

cannot start.

Defaults

For the RGOS not supporting the timers throttle spf command, the default values are as follows:

spf-delay: 5seconds;

spf-holdtime: 10 seconds.

For the RGOS supporting the timers throttle spf command, by default, the timers spf command takes

no effect. Spf-delay depends on the default configuration of the timers throttle spf command.

Command

Mode

Routing process configuration mode

Usage Guide

Smaller values of

spf-delay

and

spf-holdtime

mean that OSPF adapts to the topology change faster,

and the network convergence period is shorter, but this will occupy more CPU of the router.

The configurations of the

timers spf command

and the timers throttle spf command may

overwrite each other.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 769 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: