Ruijie RG-S29 Series Скачать руководство пользователя страница 367

Страница: 367 / 1510

Command Reference MSTP Commands

Usage Guide

If the designated port of a device does not receive a BPDU from the downlink port within a specific

period (3 seconds), the device regards a network device connected to the designated port, configures

the port as an edge port, and switches the port directly into the forwarding state. The edge port will be

automatically identified as a non-edge port after receiving a BPDU.

You can run the spanning-tree autoedge disabled command to disable Auto Edge.

Configuration

Examples

The following example disables Autoedge on the interface.

Ruijie(config)# interface gigabitethernet 1/1

Ruijie(config-if-interface-id-interface-id)# spanning-tree autoedge disabled

Related

Commands

Command

Description

show spanning-tree interface

Displays the STP configuration information of

the interface.

Platform

Description

N/A

9.19 spanning-tree bpdufilter

Use this command to enable BPDU filter on the interface. You can use the

enabled

disabled

option of the command to enable or disable the BPDU filter function on the interface.

spanning-tree bpdufilter

[

enabled

disabled

]

Parameter

Description

Parameter

Description

enabled

Enables BPDU filter on the interface.

disabled

Disables BPDU filter on the interface.

Defaults

This function is disabled by default,

Command

Mode

Interface configuration mode.

Usage Guide

If BPDU filter is enabled on a port, the port neither sends nor receives BPDUs.

Configuration

Examples

The following example enables BPDU filter on interface Gi 1/1.

Ruijie(config)# interface gigabitethernet 1/1

Ruijie(config-if-interface-id-interface-id)# spanning-tree bpdufilter enable

Related

Commands

Command

Description

show spanning-tree interface

Displays the STP configuration of the interface.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды