Ruijie RG-S29 Series Скачать руководство пользователя страница 1353

Страница: 1353 / 1510

Command Reference QoS Commands

queue bandwidth configuration.

The

queue mcast

keyword indicates configuring the minimum or maximum of the

interface bandwidth to the multicast queue on the device supporting the multicast

queue bandwidth configuration.

The

queue

keyword indicates configuring the minimum or maximum of the

interface bandwidth to the queue on the device supporting both unicast and

multicast queue bandwidth configuration.

queue-id

Queue ID. The range is from 1 to 8.

bandwidth

{

minimum

maximum

}

bandwidth

Bandwidth value. The value range depends on the specific product.

Defaults

No minimum or maximum of interface bandwidth to a queue is configured by default.

Command

Mode

Interface configuration mode

Usage Guide

N/A

Configuration

Examples

The following example configures the minimum interface bandwidth of unicast queue 1 to 5 Mbps,

and the maximum to 10 Mbps.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)# qos queue ucast 1 bandwidth maximum

10240

Ruijie(config-if-GigabitEthernet 0/1)# qos queue ucast 1 bandwidth minimum

5120

The following example configures the minimum interface bandwidth of unicast queue 2 to 2 Mbps.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)# qos queue ucast 2 bandwidth minimum

2048

The following example configures minimum interface bandwidth of multicast queue 1 to 1 Mbps, and

the maximum to 5 Mbps.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)# qos queue mcast 1 bandwidth maximum

5120

Ruijie(config-if-GigabitEthernet 0/1)# qos queue mcast 1 bandwidth minimum

1024

«
...
1351
1352
1353
1354
1355
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды