Ruijie RG-S29 Series Скачать руководство пользователя страница 542

Страница: 542 / 1510

Command Reference

DHCP Commands

4 DHCP Commands

4.1 address range

Use this command to specify the network segment range of the addresses that can be allocated by

CLASS associated with DHCP address pool. Use the

form of this command to restore the default

setting.

address range

low-ip-address

high-ip-address

no address range

Parameter

Description

Parameter

Description

low-ip-address

Start address in the network segment range.

high-ip-address

End address in the network segment range.

Defaults

By default, the associated CLASS is not configured with the network segment range. The default is

the address pool range.

Command

Mode

Address pool CLASS configuration mode.

Usage Guide

Each CLASS corresponds to one network range which must be from low address to high address, so

as to allow the duplication of network segment range between multiple CLASSes. If the CLASS

associated with the address pool is specified without configuring the corresponding network segment

range, the default network segment range of this CLASS is same as the range of the address pool

where this CLASS is.

Configuration

Examples

The following example configures the network segment of class1 associated with address pool

mypool0 ranging from 172.16.1.1 to 172.16.1.8.

Ruijie(config)#

ip dhcp pool

mypool0

Ruijie(dhcp-config)# class class1

Ruijie (config-dhcp-pool-class)# address range 172.16.1.1 172.16.1.8

Related

Commands

Command

Description

ip dhcp pool

Defines the name of the DHCP address pool and enters the DHCP

address pool configuration mode.

class

Configures the CLASS associated with the DHCP address pool and

enters the address pool CLASS configuration mode.

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды