Ruijie RG-S29 Series Скачать руководство пользователя страница 1506

Страница: 1506 / 1510

Command Reference sFlow Commands

Use this command to disable flow sampling and counter sampling on the interface.

no sflow enable

Use this command to disable flow sampling and counter sampling on the interface.

default

sflow enable

Parameter

Description

Parameter

Description

ingress

Enables sFlow sampling in ingress direction.

egress

Enables sFlow sampling in egress direction.

Defaults

The sFlow sampling function on an interface is disabled by default.

Command

Mode

Interface configuration mode

Default Level

Usage Guide

This command can be used to enable counter sampling and flow sampling for physical ports, SVI ports,

sub routed ports and aggregate ports. sFlow datagram can be output only when an IP address is

configured for the corresponding sFlow Collector.

If the direction parameter is not specified, sampling on both directions are enabled.

The SVI ports and sub routed ports support only the

ingress

parameter.

Configuration

Examples

The following example enables the sFlow sampling on interface TenGigabitEthernet 0/5.

Ruijie(config-if-TenGigabitEthernet 0/5)# sflow enable

Verification

Use the

show sflow

command to display the status of the sFlow sampling function.

Prompt

Messages

N/A

Common

Errors

N/A

Platforms

N/A

7.7 sflow flow collector

Use this command to enable the sFlow Agent to send flow samples to the sFlow Collector.

sflow flow collector

collector-id

Use this command to disable the sFlow Agent to send flow samples to the sFlow Collector.

«
...
1504
1505
1506
1507
1508
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды