Ruijie RG-S29 Series Скачать руководство пользователя страница 828

Страница: 828 / 1510

Command Reference

OSPFv3 Commands

Description

3.53 timers throttle spf

Use this command to configure, the delay for SPF calculation as well as the minimum and maximum

intervals between two SPF calculations after receiving the topology change information for OSPFv3

in the routing process configuration mode. Use the

form of this command to restore the default

setting.

timers throttle spf

spf-delay spf-holdtime spf-max-waittime

no timers throttle spf

Parameter

Description

Parameter

Description

spf-delay

Specifies an SPF calculation delay after the topology change

information is received.

The range is from 1 to 600000 in the unit of milliseconds.

spf-holdtime

Specifies a shortest interval between two SPF calculations.

The range is from 1 to 600000 in the unit of milliseconds.

spf-max-waittime

Specifies a longest interval between two SPF calculations.

The range is from 1 to 600000 in the unit of milliseconds.

Defaults

The default

spf-delay

is 1000.

spf-holdtime

is 5000 and

spf-max-waittime

is 10000.

Command

Mode

Routing process configuration mode.

Usage Guide

Spf-delay

refers to the delay from the topology change to the SPF calculation.

Spf-holdtime

refers to

the minimum interval between the first and the second SPF calculations. Then, the interval of the

consecutive SPF calculations is at least twice as the last interval till it reaches to

spf-max-waittime

. If

the interval between two SPF calculations has exceeded the required minimum value, the interval of

SPF calculation will re-start from

spf-holdtime

Smaller

spf-delay

and

spf-holdtime

value can make the topology convergence faster. Greater

spf-max-waittime

value can reduce the SPF calculations. Those configuration are flexible according

to the actual stability of the network topology.

Compared with the timers spf command, this command is more flexible. It not only speeds up the

SPF convergence calculation, but also reduces the system resources consumption of SPF calculation

as the topology changes continuously. Therefore, the timers throttle spf command is recommended.

The spf-holdtime cannot be smaller than spf-delay, or the spf-holdtime will be set to be equal

to spf-delay;

The spf-max-waitime cannot be smaller than spf-holdtime, or the spf-max-waittime will be set

to be equal to spf-holdtime automatically;

The configuration of the timers spf command and of the timers throttle spf command

are

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды