Ruijie RG-S29 Series Скачать руководство пользователя страница 490

Страница: 490 / 1510

Command Reference

ARP Commands

Defaults

This function is disabled by default.

Command Mode

Interface configuration mode.

Usage Guide

If an interface of the switch is used as the gateway of its downlink devices and counterfeit

gateway behavior occurs in the downlink devices, you can configure to send the free ARP

request message regularly on this interface to notify that the switch is the real gateway.

Configuration

Examples

The following example sets to send one free ARP request to SVI 1 per second.

Ruijie(config)#

interface vlan

Ruijie(config-if)# arp gratuitous-send interval

The following example stops sending the free ARP request to SVI 1.

Ruijie(config)#

interface vlan

Ruijie(config-if)# no arp gratuitous-send

Related Commands

Command

Description

N/A

Platform

Description

N/A

2.5 arp retry interval

Use this command to set the frequency for sending the arp request message locally, namely, the

time interval between two continuous ARP requests sent for resolving one IP address. Use the

form of this command to restore the default setting.

arp retry interval

seconds

no arp retry interval

Parameter

Description

Parameter

Description

seconds

Time for retransmitting the ARP request message in the range from

1 to 3600 in the unit of seconds.

Defaults

The default is 1.

Command

Mode

Global configuration mode.

Usage Guide

The switch sends the ARP request message frequently, and thus causing problems like network

busy. In this case, you can set the retry interval of the ARP request message longer. In general, it

should not exceed the aging time of the dynamic ARP entry.

Configuration

The following example sets the retry interval of the ARP request as 30 seconds.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды