Ruijie RG-S29 Series Скачать руководство пользователя страница 1492

Страница: 1492 / 1510

Command Reference SPAN-RSPAN Commands

The following example configures the SPAN session mirroring only the traffic permitted by the access

list.

Ruijie(config)# monitor session 3 source interface gigabitEthernet 0/3 rx acl

The following example configures a remote SPAN session.

Ruijie(config)# monitor session 10 remote-source

The following example configures the destination port of the remote SPAN session.

Ruijie(config)# monitor session 4 destination remote vlan 10 interface

gigabitEthernet 0/5

The following example configures the source VLAN of the SPAN session.

Ruijie(config)# monitor session 1 source vlan 1

The following example removes the SPAN session.

Ruijie(config)# no monitor session 1

The following example removes the source port and destination port of the SPAN session.

Ruijie(config)# no monitor session 1 source interface gigabitEthernet 0/18

Ruijie(config)# no monitor session 1 destination interface gigabitEthernet

0/18

The following example configures the SPAN session monitoring only the traffic sent from CPU.

Ruijie(config)# monitor session 3 source interface gigabitEthernet 0/3 tx cpu

The following example configures the SPAN session monitoring traffic, including the traffic sent from

CPU.

Ruijie(config)# monitor session 3 source interface gigabitEthernet 0/3 tx cpu

Ruijie(config)# monitor session 3 source interface gigabitEthernet 0/3 tx

Related

Commands

Command

Description

N/A

Platform

Description

N/A

5.3 remote-span

Use this command to configure a remote SPAN VLAN in VLAN configuration mode. Use the

form

of this command to disable the remote SPAN VLAN.

remote-span

«
...
1490
1491
1492
1493
1494
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды