Ruijie RG-S29 Series Скачать руководство пользователя страница 558

Страница: 558 / 1510

Command Reference

DHCP Commands

Platform

Description

N/A

4.22 ip dhcp ping packets

Use this command to configure the times of pinging the IP address when the DHCP server detects

address conflict in the global configuration mode. Use the

form of this command to restore the

default setting.

ip dhcp ping packets

[

number

]

no ip dhcp ping packets

Parameter

Description

Parameter

Description

number

(Optional) Number of packets in the range of 0 to 10, where 0 indicates disabling

the ping operation. The Ping operation sends two packets by default.

Defaults

The Ping operation sends two packets by default.

Command

Mode

Global configuration mode.

Usage Guide

When the DHCP server attempts to assign the IP address from the DHCP address pool, use the ping

operation to check whether this address is occupied by other hosts. Record it if the address is

occupied, otherwise, assign it to the DHCP client. The Ping operation will send up to 10 packets, two

packets by default.

Configuration

Examples

The following example sets the number of the packets sent by the ping operation as 3.

ip dhcp ping packets 3

Related

Commands

Command

Description

clear ip dhcp conflict

Clears the DHCP history conflict record.

ip dhcp ping packet

Configures the timeout time that the DHCP server waits for the Ping

response. If all the ping packets are not responded within the

specified time, it indicates that this IP address can be assigned.

Otherwise, it will record the address conflict.

show ip dhcp conflict

Displays the DHCP server detects address conflict when it assigns

an IP address.

Platform

Description

N/A

4.23 ip dhcp ping timeout

Use this command to configure the timeout that the DHCP server waits for response when it uses the

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды