Ruijie RG-S29 Series Скачать руководство пользователя страница 722

Страница: 722 / 1510

Command Reference

OSPFv2 Commands

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# ip address 172.16.10.1 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)# ip ospf dead-interval minimal hello-multiplier 3

Related

Commands

Command

Description

ip ospf hello-interval

Specifies the interval at which the OSPF sends

Hello packets

show ip ospf interface

Displays OSPF interface information.

Platform

Description

N/A

2.28 ip ospf disable all

Use this command to prevent the specified interface from generating OSPF packets. Use the

form

of this command to restore the default setting.

ip ospf disable all

no ip ospf disable all

Parameter

Description

Parameter

Description

N/A

Defaults

OSPF packets are generated on the specified interface by default.

Command

Mode

Interface configuration mode

Usage Guide

The interface configured with this command will ignore whether the network areas are matched. After

this command is configured, an interface will not generate OSPF packets even if the interface

belongs to the network; therefore, the interface does not receive or send any OSPF packets or

participate in OSPF calculation.

Configuration

Examples

The following example prevents the specified interface from generating OSPF packets.

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# ip address

172.16.10.1 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)# ip ospf disable all

Related

Commands

Command

Description

N/A

Platform

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды