Ruijie RG-S29 Series Скачать руководство пользователя страница 1409

Страница: 1409 / 1510

Command Reference VRRP Commands

Platform

Description

N/A

4.12 vrrp timers advertise

Use this command to specify the interval for the master device to send the VRRP advertisement.

Use the

form of this command to restore the default setting.

vrrp

[

ipv6

]

group

timers advertise

{

advertise-interval |

csec

centisecond-interval

}

no vrrp

[

ipv6

]

group

timers advertise

Parameter

Description

Parameter

Description

ipv6

Applies to IPv6 VRRP.

group

VRRP group number

advertise-interval

Sets the interval time in seconds between sending VRRP

advertisement.

csec

centisecond-interval

Sets the interval time in milliseconds between sending advertisement

frames from the master VRRP router in the backup group. The range

is from 50 to 99. This value is not set by default.

This parameter takes effect only for VRRPv3.

Defaults

This function is disabled by default. Once the VRRP function is enabled, the default advertisement

interval of the master device is one second.

Command

Mode

Interface configuration mode

Usage Guide

If the current device becomes the master device in the VRRP group, it will notify its VRRP status,

priority and other information by sending the VRRP advertisement in the set interval.

Based on the RFC specification, the maximum advertisement interval of the IPv4/IPv6 VRRPv3 group

is 40 seconds. The advertisement interval can be configured larger than 40 seconds, but the effective

advertisement interval is 40 seconds.

Configuration

Examples

The following example sets the IPv4 VRRP advertisement interval as 4 seconds.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

Ruijie(config-if-GigabitEthernet 0/0)#ip address 10.0.1.1 255.255.255.0

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 ip 10.0.1.20

Ruijie(config-if-GigabitEthernet 0/0)#vrrp 1 timers advertise 4

The following example sets the IPv6 VRRP advertisement interval as 4 seconds.

Ruijie#configure terminal

Ruijie(config)#interface GigabitEthernet 0/0

Ruijie(config-if-GigabitEthernet 0/0)#no switchport //used on the switch.

«
...
1407
1408
1409
1410
1411
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды