Ruijie RG-S29 Series Скачать руководство пользователя страница 720

Страница: 720 / 1510

Command Reference

OSPFv2 Commands

2.26 ip ospf database-filter all out

Use this command to stop advertising LSAs of an interface, that is, the LSA update packets are not

sent on the interface. Use the

form of the command to restore the default setting.

ip ospf database-filter all out

no ip ospf database-filter

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled and all LSA update packets can be sent on the interface by default.

Command

Mode

Interface configuration mode

Usage Guide

To stop sending LSA update packets on the interface, enable this function on the interface.

Then, the device maintains the neighboring connections and accepts LSAs from neighbors, but stops

sending LSAs to neighbors.

Configuration

Examples

The following example stops sending LSA update packets of fastEthernet 0/1.

Ruijie(config)# interface fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# ip address

172.16.10.1 255.255.255.0

Ruijie(config-if-FastEthernet 0/1)# ip ospf database-filter all out

Related

Commands

Command

Description

N/A

Platform

Description

N/A

2.27 ip ospf dead-interval

Use this command to configure the interval for determining the death of an interface neighbor in

interface configuration mode. Use the

form of this command to restore the default setting.

ip ospf dead-interval

{

seconds

| minimal hello-multiplier

multiplier

}

no ip ospf dead-interval

Parameter

Description

Parameter

Description

seconds

Defines the interval for determining the neighbor death in seconds.

The range is from 0 to 2,147,483,647.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды