Ruijie RG-S29 Series Скачать руководство пользователя страница 414

Страница: 414 / 1510

Command Reference LLDP Commands

Platform

Description

N/A

11.21 lldp timer tx-interval

Use this command to set the interval of sending the LLDP packets. Use

form of this command to

restore the default setting.

lldp timer tx-interval

seconds

no lldp timer tx-interval

Parameter

Description

Parameter

Description

seconds

Interval of sending the LLDP packets, in the range from 5 to 32768 in

the unit of seconds.

Defaults

The default is 30.

Command

Mode

Global configuration mode.

Usage Guide

N/A

Configuration

Examples

The following example sets the interval of sending the LLDP packets to 10 seconds.

Ruijie#config

Ruijie(config)#lldp timer tx-interval 10

Related

Commands

Command

Description

show lldp status

Displays LLDP status information.

Platform

Description

N/A

11.22 lldp tlv-enable

Use this command to configure the types of advertisable TLVs. Use

the

form of this command to

restore the default setting.

lldp tlv-enable

{

basic-tlv

{

all | port-description | system-capability | system-description |

system-name

}

| dot1-tlv

{

all | port-vlan-id | protocol-vlan-id

[

vlan-id

]

| vlan-name

[

vlan-id

]

}

dot3-tlv

{

all | link-aggregation | mac-physic | max-frame-size | power

}

| med-tlv

{

all | capability

| inventory | location

{

civic-location | elin

}

identifier

| network-policy profile

[

profile-num

]

power-over-ethernet

} }

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды