Ruijie RG-S29 Series Скачать руководство пользователя страница 1354

Страница: 1354 / 1510

Command Reference QoS Commands

Related

Commands

Command

Description

show qos bandwidth

[

interfaces

interface-id

]

Displays the interface bandwidth of the queue.

Platform

Description

N/A

2.16 rate-limit

Use this command to configure rate limiting on the interface. Use the

default

form of this

command to remove rate limiting from the interface.

rate-limit { input | output }

bps burst-size

no rate-limit

{

input | output

}

default rate-limit

{

input | output

}

Parameter

Description

Parameter

Description

input

Configures input rate limiting.

output

Configures output rate limiting.

bps

Bandwidth limit value per second (The unit is KBits). This value

depends on the specific product.

burst-size

Burst traffic limit value (The unit is KBytes). This value depends on

the specific product.

Defaults

Rate limiting is not configured by default.

Command

Mode

Interface configuration mode.

Usage Guide

N/A

Configuration

Examples

The following example configures the rate limit value to 10 Mbps, and the burst traffic limit value to

256 Kbps.

Ruijie(config)# interface gigabitethernet 1/3

Ruijie(config-if-GigabitEthernet 1/3)# rate-limit input 10240 256

Related

Commands

Command

Description

show mls qos rate-limit

[

interface

interface-id

]

Displays the rate limiting configuration of the

interface.

Platform

Description

N/A

«
...
1352
1353
1354
1355
1356
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды