Ruijie RG-S29 Series Скачать руководство пользователя страница 168

Страница: 168 / 1510

Command Reference

Syslog Commands

severity

Log information severity level; lower the level is, higher the

severity is, ranging from 0 to 7

Defaults

The maximum number of logs that can be re-directed each second is 200 by default.

Command

Mode

Global configuration mode

Usage Guide

This command is used to control the output of log information by system re-direction. You can use

this command to prevent a slave or backup device from re-directing a large number of logs to the

host.

Configuration

Examples

The following example sets the maximum number of logs (including debug) that can be re-directed

from a slave device to the host each second at 10, excepting logs on and above the warning severity

level:

Ruijie(config)#logging rd rate-limit 10 except warnings

Related

Commands

Command

Description

show logging count

Displays log information about modules of the system.

show logging

Displays basic configuration of log modules and log

information in the buffer.

Platform

Description

N/A

8.25 logging server

Use this command to send the logs to the specified Syslog Sever in global configuration mode. Use the

form of this command to remove the setting. Use the

default

form of this command to restore the

default setting.

logging server

{

ip-address

ipv6

ipv6-address

} [

udp-prot

port

]

no logging server

{

ip-address

ipv6

ipv6-address

}

no logging server

{

ip-address

ipv6

ipv6-address

}

udp-prot

Parameter

Description

Parameter

Description

ip-address

IP address of the host that receives log information.

ipv6-address

Specifies IPV6 address for the host receiving the logs.

udp-port

port

Specifies the port number for the specified host (The default

port number is 514).

Defaults

No log is sent to any syslog server by default.

Command

Global configuration mode

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды