Ruijie RG-S29 Series Скачать руководство пользователя страница 339

Страница: 339 / 1510

Command Reference Private VLAN Commands

One host port can be associated with only one PVLAN pair.

Configuration

Examples

The following example associates the secondary VLAN with the primary VLAN on the host port.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if)# switchport mode private-vlan host

Ruijie(config-if)# switchport private-vlan host-association 22 23

Ruijie(config-if)# default switchport private-vlan host-asscioation

Ruijie(config-if)# switchport private-vlan host-association 22 25

Related

Commands

Command

Description

show vlan private-vlan

N/A

Platform

Description

N/A

7.8 switchport private-vlan mapping

Use this command to configure the secondary VLAN for the promiscuous port. Use the

default

form of this command to restore the default setting.

switchport private-vlan mapping

p_vid

{

svlist

add

svist

remove

svlist

}

no switchport private-vlan mapping

default switchport private-vlan mapping

Parameter

Description

Parameter

Description

p_vid

Indicates the primary VLAN ID in a PVLAN pair.

svlist

Indicates the secondary VLAN associated with a promiscuous port.

Layer-2 association must be performed between it and

p_vid

add

Adds a secondary VLAN to be associated with a port.

remove

Cancels the secondary VLAN associated with a port.

Defaults

This function is disabled by default.

Command

mode

Interface configuration mode

Usage Guide

The port mode must be configured as the promiscuous mode.

Layer-2 association must be performed between the primary and secondary VLAN.

Configuration

Examples

The following example configures the secondary VLAN for the promiscuous port.

Ruijie(config)# interface gigabitEthernet 0/1

Ruijie(config-if)# switchport mode private-vlan

promiscuous

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды