Ruijie RG-S29 Series Скачать руководство пользователя страница 1282

Страница: 1282 / 1510

Configuration Guide NFPP Commands

VLAN interface ND-guard remain-time(s)

---- --------- -------- --------------

- Gi4/2 ns-na-guard 174

- Gi4/2 rs-guard 98

- Gi4/2 ra-redirect-guard 127

Total: 3 hosts

Platform

Description

N/A

21.100

trusted-host

Use this command to set the trusted hosts free form monitoring.

Use the

default

form of this command to restore the default setting,

trusted-host

{

mac mac_mask

ip mask

IPv6/prefixlen

}

no trusted-host

{

all |

mac mac_mask

mask | IPv6/prefixlen

}

default trusted-host

Parameter

Description

Parameter

Description

Sets the IP address

mac

MAC address

mac_mask

MAC address mask

IPv6/prefixlen

IPv6 address and mask length

mask

IP mask

all

Deletes the configuration of all trusted hosts with the no form of this

command.

Defaults

N/A

Command

Mode

NFPP define configuration mode

Usage Guide

The administrator can use this command to set the trusted host free from monitoring. The ICMP

packets are allowed to be sent to the trusted host CPU without any rate-limit and warning

configuration. Configure the mask to set all hosts in one network segment free from monitoring.

UP to 500 trusted hosts are supported.

Before configuring the trusted-host, the match type must be configured. If the message type

configured by the match is Ipv4, the Ipv6 trusted addresses are not allowed. In the same way, if the

message type is IPv6, the IPv4 trusted addresses are not allowed.

Configuration

Examples

The following example sets the trusted hosts free form monitoring.

Ruijie(config)# nfpp

Ruijie(config-nfpp)# define tcp

«
...
1280
1281
1282
1283
1284
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды