Ruijie RG-S29 Series Скачать руководство пользователя страница 772

Страница: 772 / 1510

Command Reference

OSPFv2 Commands

Usage Guide

The default setting is recommended if the network needs to be fast converged. For the instable

network where multiple inter-area and external routes exist, if you want to optimize the route

calculation and save the CPU resources, increase the delay time.

Configuration

Examples

The following example sets the .delay time of the inter-area route calculation to one second.

Ruijie(config)# router ospf 1

Ruijie(config-router)# timers throttle route inter-area 1000

Related

Commands

Command

Description

N/A

Platform

Description

N/A

2.66 timers throttle spf

Use this command to configure the topology change information for OSPF, including the delay for

SPF calculation as well as the interval between two SPF calculations in routing process configuration

mode. Use the

form of this command to restore the default setting.

timers throttle spf

spf-delay spf-holdtime spf-max-waittime

no timers throttle spf

Parameter

Description

Parameter

Description

spf-delay

Defines the SPF calculation waiting period, in the unit of milliseconds,

in the range from1 to 600,000. After receiving the topology change,

the OSPF routing process must wait for the specified period to start

the SPF calculation.

spf-holdtime

Defines the interval between two SPF calculations in seconds in the

range from1 to 600,000.

spf-max-waittime

Defines the maximum interval between two SPF calculations, in

milliseconds in the range from1 to 60,0000.

Defaults

The default configurations are as follows:

spf-delay: 1000ms;

spf-holdtime: 5000ms;

spf-max-waittime: 10000ms.

Command

Mode

Routing process configuration mode

Usage Guide

The spf-delay parameter indicates the delay time of the topology change to the SPF calculation.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды