Ruijie RG-S29 Series Скачать руководство пользователя страница 1021

Страница: 1021 / 1510

Configuration Guide 802.1X Commands

Defaults

By default, no limit is set for the auth-user number.

Command

mode

Interface configuration mode

Usage Guide

This command is used to limit the number of users to be authenticated on a specific port.

Configuration

Examples

The following example sets the maximum auth-user number on a controlled interface.

Ruijie(config-if)# dot1x default-user-limit 10

Related

Commands

Command

Description

show dot1x port-control

interface fastEthernet 0/10

Displays the number of users allowed by a specific 802.1X

interface.

show dot1x port-control

interface fastEthernet 0/10

Displays the number of users allowed by a specific 802.1X

interface.

Platform

Description

N/A

4.24 dot1x dynamic-vlan enable

Use this command to enable dynamic VLAN.

Use the

form of this command to disable the function.

dot1x dynamic-vlan enable

no dot1x dynamic-vlan enable

Parameter

Description

Parameter

Description

N/A

Defaults

Dynamic VLAN is disabled by default.

Command

Mode

Interface configuration mode

Usage Guide

This command is used to assign VLANs to authenticated users dynamically.

Configuration

Examples

The following example enables dynamic VLAN.

Ruijie(config-if)# dot1x dynamic-vlan enable

Related

Commands

Command

Description

show dot1x

Displays the information about 802.1X.

«
...
1019
1020
1021
1022
1023
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды