Ruijie RG-S29 Series Скачать руководство пользователя страница 917

Страница: 917 / 1510

Command Reference

IPv4 Multicast Routing Commands

Multicast Switching Cache Table

(192.168.195.23, 233.3.3.3, 1), SYNC, MTU:0, 1 OIFs

VLAN 1(0): 1 OPORTs, REQ: DONE

OPORT 6, IGMP-SNP, REQ: DONE

The fields in the execution of the

show mrf mfc

command are described in the following table.

Field

Description

192.168.195.23

Source address of the entry.

233.3.3.3

Group address of the entry.

Vlan id where the incoming interface of the entry is.

SYNC

The entry has been synchronized to the hardware.

MTU

MTU value

OIFs

Layer-3 outgoing interface number.

VLAN1(0)

The vlan where the layer-3 outgoing interface oif is.

1 OPORTs

The number of layer-2 port in the layer-3 outgoing oif.

REQ: DONE

This oif configuration on the hardware has done.

OPORT 6

The layer-2 port in the oif with index 6.

IGMP-SNP

This port is created by the IGMP SNOOPING protocol. This

value can also be the PIM-SNP, which means this port is

created by the PIM SNOOPING protocol. And the ROUTER

means this port is created by the layer-3 protocol.

REQ: DONE

The port configuration on the hardware has done.

1.4 show msf nsf

Use this command to show the configuration of continuous multicast forwarding.

show msf nsf

Parameter

Description

Parameter

Description

Command Mode

Privileged EXEC mode/Global configuration mode/Interface EXEC mode

Examples

The following example shows the configuration of continuous multicast forwarding.

Ruijie# show msf nsf

Multicast HA Parameters

---------------------------------------------------+------+

protocol convergence timeout 120 secs

flow leak interval 20 secs

Ruijie#

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды