Ruijie RG-S29 Series Скачать руководство пользователя страница 271

Страница: 271 / 1510

Command Reference Interface Commands

1.23 show interfaces counters

Use this command to display the received and transmitted packet statistics.

show interfaces

[

interface-type interface-number

]

counters

[

increment

error

rate

summary

]

[

down

]

Parameter

Description

Parameter

Description

interface-type

interface-number

(Optional) The interface type and ID.

increment

Displays the packet statistics increased during the last sample

interval.

error

Displays error packet statistics.

rate

Displays packet receiving and transmitting rate.

summary

Displays packet statistics summary.

(Optional) Displays the port up statistics.

down

(Optional) Displays the port down statistics.

Defaults

N/A

Command

Mode

Any CLI mode

Usage Guide

If you do not specify an interface, the packet statistics on all interfaces are displayed.

Configuration

Examples

The following example displays packet statistics on interface GigabitEthernet 0/1.

Ruijie#show interfaces GigabitEthernet 0/1 counters

Interface : GigabitEthernet 0/1

5 minute input rate : 9144 bits/sec, 9 packets/sec

5 minute output rate : 1280 bits/sec, 1 packets/sec

Rxload : 1%

InOctets : 17310045

InPkts : 1000(Unicast: 10%, Multicast: 10%, Broadcast: 80%)

InUcastPkts : 100

InMulticastPkts : 100

InBroadcastPkts : 800

Txload : 1%

OutOctets : 1282535

OutPkts : 1000(Unicast: 10%, Multicast: 10%, Broadcast: 80%)

OutUcastPkts : 100

OutMulticastPkts : 100

OutBroadcastPkts : 800

Undersize packets : 0

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды