Ruijie RG-S29 Series Скачать руководство пользователя страница 1119

Страница: 1119 / 1510

Configuration Guide

Storm Control Commands

Use this command to enable the storm suppression for multicast packets.

Use the

default

form of this command to restore the default setting.

storm-control

multicast

[ {

level

percent

pps

packets

rate-bps

} ]

no storm-control

multicast

default storm-control

multicast

Use this command to enable the storm suppression for broadcast packets.

Use the

default

form of this command to restore the default setting.

storm-control

broadcast

[ {

level

percent

pps

packets

rate-bps

} ]

no storm-control broadcast

default storm-control broadcast

Parameter

Description

Parameter

Description

level

percent

Sets the bandwidth percentage, for example, 20 means 20%.

pps

packets

Sets the pps, which means packets per second.

rate-bps

Rate allowed

Defaults

This function is disabled by default.

Command

Mode

Interface configuration mode

Usage Guide

Too many broadcast, multicast or unicast packets received on a port may cause storm and thus slow

network and increase timeout. Protocol stack implementation errors or wrong network configuration

may also lead to such storms.

A device can implement the storm suppression to a broadcast, a multicast, or a unicast storm

respectively. When excessive broadcast, multicast or unknown unicast packets are received, the

switch temporarily prohibits forwarding of relevant types of packets till data streams are recovered to

the normal state (then packets will be forwarded normally).

Configuration

Examples

The following example enables the multicast storm suppression on FastEthernet 0/1 and sets the

allowed rate to 4M.

Ruijie(config)# int fastEthernet 0/1

Ruijie(config-if-FastEthernet 0/1)# storm-control multicast 4096

Related

Commands

Command

Description

show storm-control

Displays storm suppression information.

Platform

Description

N/A

«
...
1117
1118
1119
1120
1121
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды