Ruijie RG-S29 Series Скачать руководство пользователя страница 800

Страница: 800 / 1510

Command Reference

OSPFv3 Commands

Command

Mode

Interface configuration mode.

Usage Guide

After receiving the database description message, the OSPFv3 device will check whether the MTU of

neighbor interface is the same as its own MTU. If the received database description message

indicates an MTU greater than its own

interface’s MTU, the neighbor relationship cannot be

established. This can be fixed by disabling the MTU check.

Configuration

Examples

The following example disables the MTU check function on the ethernet 1/0.

Ruijie(config)#

interface ethernet

1/0

Ruijie(config-if)#

ipv6 ospf mtu-ignore

Related

Commands

Command

Description

ipv6 router ospf

Starts the OSPFv3 routing process.

ipv6 mtu

Sets the value of IPv6 MTU of the interface.

Platform

Description

N/A

3.25 ipv6 ospf neighbor

Use this command to configure the OSPFv3 neighbor manually. Use the

form of this command to

restore the default setting.

ipv6 ospf neighbor

ipv6-address

[ [

cost

<1-65535> ] [ poll-interval <0-2147483647> | priority

<0-255>]] [instance

instance-id

]

no ipv6 ospf neighbor

ipv6-address

[[cost <1-65535>] [

poll-interval

< 0-2147483647 > |

priority

0-255 > ] ] [

instance

instance-id

]

Parameter

Description

Parameter

Description

cost

cost

(Optional) Configures the cost to each neighbor in point-to-multipoint

network. It is not defined by default, where the cost configured on the

interface will be used. It ranges from 1 to 65535.

Only the networks of the point-to-multipoint type support this option.

poll-interval

seconds

(Optional) Interval for polling the neighbors (in seconds), which

ranges from 1 to 2147483647.

Only the networks of the non-broadcast (NBMA) type support this

option.

priority

priority

(Optional) Configures the priority value of non-broadcast network

neighbors, which ranges from 0 to 255.

Only the non-broadcast (NBMA) type network supports this option.

instance

instance-id

(Optional) Configures the specific OSPFv3 instance on the interface,

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды