Ruijie RG-S29 Series Скачать руководство пользователя страница 464

Страница: 464 / 1510

Command Reference ERPS Commands

Ruijie(config)# interface fastEthernet 0/2

Ruijie(config-if)# switchport mode trunk

Ruijie(config-if)# exit

# Enter the ERPS configuration mode.

Ruijie(config)# erps raps-vlan 4093

# Add the ports that participate in the ERPS protocol computing to the Ethernet ring.

Ruijie(config-erps4093)# ring-port west fastEthernet 0/1 east fastEthernet

0/2

# Enable the ERPS function for the specified ring.

Ruijie(config-erps4093)#state enable

# Enable the global ERPS function.

Ruijie(config-erps4093)# exit

Ruijie(config)# erps enable

Related

Commands

Command

Description

erps enable

Enable the global ERPS protocol.

Platform

Description

N/A

13.10 sub-ring tc-propagation

Use this command to specify the devices corresponding to the crossing node on the crossing ring

whether to send out the notification when the subring topology changes.

sub-ring tc_propagation enable

no sub-ring tc_propagation

Parameter

Description

Parameter

Description

N/A

Defaults

By default, the topology changing notification is not sent.

Command

Mode

EPRS configuration mode.

Usage Guide

This command is just needed to be configured on the crossing nodes on the crossing ring.

Configuration

The following example is configured when the subring topology changes.

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды