Ruijie RG-S29 Series Скачать руководство пользователя страница 843

Страница: 843 / 1510

Command Reference

RIPng Commands

4.15 timers

Use this command to adjust the RIPng timer. Use the

form of this command to restore the default

settings.

timers

update invalid flush

no timers

Parameter

Description

Parameter

Description

update

Sets the routing update time, in seconds. The update parameter

defines the period of sending the routing update packets by the

device. The invalid and flush parameter reset once the update

packets are received.

invalid

Sets the routing invalid time, in seconds, starting from receiving the

last valid update packet. The invalid parameter defines the invalid

time for the un-updated routing in the routing list. The routing invalid

time shall be three times larger than the routing update time. The

routing will be invalid if no update packets are received within the

routing invalid time, and it will reset if the update packets are received

within the invalid time.

flush

Sets the routing flush time, in seconds, starting from RIPng entering

to invalid state. The invalid routing will be removed from the routing

list if the flush time expires.

Defaults

The default update time is 30 seconds; the default invalid time is 180 seconds; and the default flush

time is 120 seconds.

Command

mode

Routing process configuration mode.

Usage Guide

Adjusting the above time may speed up the RIPng convergence time and the troubleshooting time.

The RIPng time must be consistent for the devices connecting to the same network. You are not

recommended to adjust the RIP time, except for the specific requirement.

Use the

show ipv6 rip

command to view the current RIPng time parameter setting.

In the low-speed link, with the short time configured, large amount of the update packets consumes a

lot of bandwidth. Generally, the short time can be configured in the Ethernet or 2Mbps-higher line to

shorten the convergence time of the network routing.

Configuration

Examples

The following example shows how to send the RIP update packets every 10 seconds. The routing will

be invalid if no update packets are received within 30 seconds, and the routing will be removed after

being invalid for 90 seconds.

Ruijie(config)# ipv6 router rip

Ruijie(config-router)# timers 10 30 90

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды