Ruijie RG-S29 Series Скачать руководство пользователя страница 1019

Страница: 1019 / 1510

Configuration Guide 802.1X Commands

no dot1x critical vlan

Parameter

Description

Parameter

Description

N/A

Defaults

This function is disabled by default.

Command

Mode

Interface configuration mode

Usage Guide

With this function enabled, if no user authentication is performed on the ports initially, after all

RADIUS servers are invalidated, the user will initiate the authentication and the port will enter the IAB

status and to be added to the VLAN configured. If this function is disabled, the VLAN of the port is not

changed when the port is in the IAB status.

Configuration

Examples

Ruijie(config-if-GigabitEthernet 0/5)#dot1x critical vlan 10

Related

Commands

Command

Description

N/A

Platform

Description

N/A

4.21 dot1x dbg-filter

Use this command to enable debug information print for a user with a specified MAC address.

Use the

form of this command to clear the debug information.

dot1x dbg-filter

H.H.H

no dot1x dbg-filter

H.H.H

Parameter

Description

Parameter

Description

H.H.H

The MAC address of a user

Defaults

Debug information of all authentication users is printed by default.

Command

mode

Global configuration mode

Usage Guide

Use this command to print the debug information of a specific user If you want to locate the fault on

the network where there are multiple users.

Configuration

Examples

The following example prints the debug information of the device with the specified MAC address.

Ruijie(config)# dot1x dbg-filter 00d0.f800.0001

«
...
1017
1018
1019
1020
1021
...
»

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды