Ruijie RG-S29 Series Скачать руководство пользователя страница 270

Страница: 270 / 1510

Command Reference Interface Commands

admin duplex mode is AUTO, oper duplex is Unknown

admin speed is AUTO, oper speed is Unknown

flow receive control admin status is OFF,flow send control admin status is

OFF,flow receive control oper status is Unknown,flow send control oper status is

Unknown

broadcast Storm Control is OFF,multicast Storm Control is OFF,unicast Storm Control

is OFF

Port-type: hybrid

Tagged vlan id:2

Untagged vlan id:none

5 minutes input rate 0 bits/sec, 0 packets/sec

5 minutes output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer, 0 dropped

Received 0 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort

0 packets output, 0 bytes, 0 underruns , 0 dropped

0 output errors, 0 collisions, 0 interface resets

The following example displays the layer-2 information of the Gi0/1.

Ruijie# show interfacesgigabitEthernet

0/1

switchport

Interface Switchport ModeAccess Native Protected VLAN lists

--------- ---------- --------- ------ ------ ---------

GigabitEthernet 0/1 enabled Access 11 Disabled ALL

Related

Commands

Command

Description

duplex

Duplex

flowcontrol

Flow control status.

interface gigabitEthernet

Selects the interface and enter the interface

configuration mode.

interface aggregateport

Creates or accesses the aggregate port, and enters

the interface configuration mode.

interface vlan

Creates or accesses the switch virtual interface

(SVI), and enters the interface configuration mode.

shutdown

Disables the interface.

speed

Configures the speed on the port.

switchport priority

Configures the default 802.1q interface priority.

switchport protected

Configures the interface as a protected port.

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды