Ruijie RG-S29 Series Скачать руководство пользователя страница 718

Страница: 718 / 1510

Command Reference

OSPFv2 Commands

mode. Use the

form of this command to restore the default setting.

ip ospf authentication-key

[

0 | 7

]

key

no ip ospf authentication-key

Parameter

Description

Parameter

Description

Displays the key in plain text.

Displays the key in cipher text.

key

Key containing at most eight characters.

Defaults

It is disabled by default.

Command

Mode

Interface configuration mode

Usage Guide

The

ip ospf authentication-key

command configures the key that will be inserted in all OSPF packet

headers. As a result, if the keys are inconsistent, the OSPF neighbor relationship cannot be

established between two devices directly connected, and thus route information exchange is

impossible.

The keys may vary by interface, but the devices that are connected to the same physical network

segment must use the same key.

To enable the OSPF area authentication, execute the area authentication command in routing

process configuration mode.

The authentication can be enabled separately on an interface by executing the ip ospf authentication

command in interface configuration mode. When both the interface and the area are configured with

authentication, the one for the interface takes precedence.

Configuration

Examples

The following example configures the OSPF authentication key ospfauth for fast Ethernet

0/1

Ruijie (config)#interfacefastEthernet0/1

Ruijie(config-if-FastEthernet 0/1)# ipaddress

172.16.1.1

255.255.255.0

Ruijie(config-if-FastEthernet 0/1)# ip ospf authentication-key ospfauth

Related

Commands

Command

Description

area authentication

Enables OSPF area authentication and defines

authentication mode

ip ospf authentication

Enables authentication on the interface and

defines authentication mode

Platform

Description

N/A

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды