Ruijie RG-S29 Series Скачать руководство пользователя страница 277

Страница: 277 / 1510

Command Reference Interface Commands

Parameter

Description

Parameter

Description

interface-type

interface-number

The interface type and ID.

transceiver

Displays the transceiver information.

alarm

Displays the alarm message of the transceiver. If there is no alarm

message, it is displayed as None.

diagnosis

Displays the diagnostic parameters of the transceiver.

Defaults

N/A

Command

Mode

Privileged EXEC mode

Usage Guide

If you do not specify an interface, the transceiver information of all interfaces is displayed.

Configuration

Examples

The following example displays the transceiver information of interface Gigabitethernet 5/4.

Ruijie#show interfaces GigabitEthernet 5/4 transceiver

Transceiver Type : 1000BASE-SX-SFP

Connector Type : LC

Wavelength(nm) : 850

Transfer Distance :

50/125 um OM2 fiber

-- 550m

62.5/125 um OM1 fiber

-- 270m

Digital Diagnostic Monitoring : YES

Vendor Serial Number : 101680093602489

The following example displays the alarm message of the transceiver of interface Gigabitethernet 5/4.

Ruijie#show interfaces GigabitEthernet 5/4 transceiver alarm

gigabitEthernet 5/4 transceiver current alarm information:

RX loss of signal

The following example displays the diagnostic parameters of the transceiver of interface

Gigabitethernet 5/4.

Ruijie#show interfaces GigabitEthernet 5/4 transceiver diagnosis

Current diagnostic parameters[AP:Average Power]:

Temp(Celsius) Voltage(V) Bias(mA) RX power(dBm) TX

power(dBm)

38(OK) 3.20(OK) 0.04(OK)
-40.00(alarm)[AP] -40.00(alarm)

Related

Commands

Command

Description

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Ruijie RG-S29 Series, Справочник по командам, Страница: 277 / 1510

Результаты поиска

Содержание RG-S29 Series

Отзывы: