Ruijie RG-S29 Series Скачать руководство пользователя страница 458

Страница: 458 / 1510

Command Reference ERPS Commands

Commands

N/A

Platform

Description

N/A

13.5 protected-instance

Use this command to configure the VLAN protected by the Ethernet ring to implement the load

balance function.

protected-instance

instance-id-list

no protected-instance

Parameter

Description

Parameter

Description

instance-id-list

Instance protected by this Ethernet ring. (The VLANs corresponding

to these instances are the VLANs protected by the Ethernet ring.)

Defaults

By default, all VLANs are protected.

Command

Mode

EPRS configuration mode.

Usage Guide

The protected VLAN consists of the R-APS VLAN of this Ethernet ring and the data VLAN protected

by this Ethernet ring.

Configuration

Examples

Suppose that the ERP1 and ERP2 are configured on the switch to implement the load balance. The

R-APS VLAN of the ERPS1 is 100, the protected data VLAN is in the range of 1 to 99 and 101-2000,

the R-APS VLAN of the ERPS2 is 4093, and the protected data VLAN is in the range of 2001 to 4092

and 4094. Configuration for the load balance is shown as below:

# Enter the privileged EXEC mode.

Ruijie# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

# Configure the VLAN configured by the ERP1.

Ruijie(config)# spanning-tree mst configuration

Ruijie(config-mst)# instance 1 vlan 100, 1-99, 101-2000

Ruijie(config-mst)# exit

Ruijie(config)# erps raps-vlan 100

Ruijie(config-erps100)#protected-instance 1

# Configure the VLAN configured by the ERP2.

Ruijie(config)# spanning-tree mst configuration

Ruijie(config-mst)# instance 2 vlan 4093, 2001-4092, 4094

Содержание RG-S29 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды

Ruijie RG-S29 Series, Справочник по командам

Результаты поиска

Содержание RG-S29 Series

Отзывы:

Похожие инструкции для RG-S29 Series

Бренды по названию

Популярные бренды